My Education >> Search Results

i need help plz,? 1) which one of the following tools can be used to cut external threads on bolts or rods? a)tap b)die c)reamer d)screw extractor 2) how much current can a 12-gauge copper wire carry? a)15 amps b)20 amps c)25 amps d)30 amps 3) when measuring current, always place any type of meter in a)series b)the ohms position c)the leakage position d)a parallel position to the circuit 4) your customer has connected a 1000- watts microwave oven and a 600-watt mixer to a 15-amp branch service line for the kitchen. what is the actual current draw, and will the circuit breaker trip if these are the only loads in what line? a)16.00amps, no b)16.00amps, yes c)14.24amps, no d)14.24amps, ... (Asked by steven)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
1) B 2)B 3) D 4) D I think this is right but i would reference the NEC. it will discuss equation and theory in detail as well as wiring technique...(Answered by D B)

View Entire Answer \| Report Abuse \| See it in Y!

whats something favorite in 1957 besides poodle skirts and hot rods? doing a research project looking for more helpful sites etc. 1957 project-----literature, popular amer music, politics,famous people, newsworthy items,fads, cultural items, popular foods, sports, and most importantly family activities. ... (Asked by Sarah)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
Stroll Down Memory Lane-1957...(Answered by kimandchris2)

View Entire Answer \| Report Abuse \| See it in Y!

Anyboody please help multiple choice. Thanks? 1. Change the fraction 93/1.000 to a decimal. A. 0.93 B. 0.093 C.0.0093 D.0.00093 2, John measured the diameter of four steel rods, Compare his measurements below. Which one is the largest? 3. Change the fraction 13/20 to a decimal. A. 0,015 B. 0.15 C. 0.065 D. 0.65 4. A chemist weighed three separate test samples at 0.17 gram, 0.204 gram, and 2.3 grams. What is the total weight of the three samples? A.2.44 grams B.2.521 grams C.2.674 grams D.3.97 grams 5.11 + 1 + 0.01 + 0.11 + 0.111 ... (Asked by lapatskiy)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
a -d-c-b...(Answered by submersed2)

View Entire Answer \| Report Abuse \| See it in Y!

How is a boning rod used? ... (Asked by Keneisha)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
Boning Rods Boning rods are used to set the pegs that mark the center of the road, and ensure that the pegs lie in the same plane. The surface of a road or bush path built without the help of boning rods has many small dips and bumps, reflecting the shape of the ground under the road. Boning rods help assure that the surface of the road will be level. Boning rods are made of ordinary timber one inch thick. They always come in sets of three. All three boning rods in a set must be identical. For this reason, ...(Answered by flamingo_sandy)

View Entire Answer \| Report Abuse \| See it in Y!

plz help me? 1. The type of two-stroke engine that uses a spinning plate with a hole in it to control the flow of fuel to the cylinder is called a A. reed-valve engine. B. rotary-valve engine. C. piston-port engine. D. plate-port engine. 2. The purpose of the piston rings is to A. prevent the piston from moving up and down too fast in the cylinder. ... (Asked by steven)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
Those of us who actually worked our way through school aren't going to give you a free ride, sorry. If you want passing grades you have to earn them....(Answered by Spy Girl)

View Entire Answer \| Report Abuse \| See it in Y!

this is out of this world!! :'(? A uniform thin rod of length 0.56 m and mass 3.8 kg can rotate in a horizontal plane about a vertical axis through its center. The rod is at rest when a 2.4 g bullet traveling in the rotation plane is fired into one end of the rod. As viewed from above, the direction of the bullet's velocity makes angle = 57° with the rod. If the bullet lodges in the rod and the angular velocity of the rod is 15 rad/s immediately after the collision, what is the bullet's speed just before impact? is there NO ONE out there to ... (Asked by kenyankid)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
wat grade r U in?...(Answered by dude)

View Entire Answer \| Report Abuse \| See it in Y!

plz help me? 1. The type of two-stroke engine that uses a spinning plate with a hole in it to control the flow of fuel to the cylinder is called a A. reed-valve engine. B. rotary-valve engine. C. piston-port engine. D. plate-port engine. 2. The purpose of the piston rings is to A. prevent the piston from moving up and down too fast in the cylinder. ... (Asked by steven)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
Boy your crazy!! Do some studying or look up the answer's. We ain't here to do your homework for ya...(Answered by Dez)

View Entire Answer \| Report Abuse \| See it in Y!

If rod bearing clearance specks is .001" would this be .00075" clearance ful circle or .001" full circle ... (Asked by Mr. Don't know)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
.001 total clearance. if journal is 1.500 then when bolted together rod bearing inside diamter should be 1.501...(Answered by brew14me13)

View Entire Answer \| Report Abuse \| See it in Y!

What unit of measurement is equal to 1/8 of a mile (or 40 rods)? ... (Asked by trivia buff)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
1 furlong....(Answered by Drew)

View Entire Answer \| Report Abuse \| See it in Y!

how do u cut a rod of 7meters into 7 equal pieces by cutting it only 3 times? u can do wht ever u want but only times u shud cut and u shud get 7 equal pieces ... (Asked by rajiv_kunisetty)
View Entire Question \| Report Abuse \| Similar Questions \| See it in Y!
A.
first cut it into two rods of 4&3 metres.then place them side by side and cut the 4mt. rod into two 2mt. rods&the 3mt rod into 2mt&1mt rods in 1 cut.place the three 2mt.rods side by side and cut them into 1 mt. rod each .3 cuts and seven 1mt.rods....(Answered by subharee s)

View Entire Answer \| Report Abuse \| See it in Y!

Note: We are not affiliated with Yahoo! Answers in any way. All the content is retrieved from Yahoo! Answers. We are not responsible for the content. For more information, please see the term of service. The above content was retrieved on December 10 2008 03:45:20.from Yahoo! Answers (Category Home > Education & Reference > General - Education & Reference). We are neither affiliated with the authors of this page nor responsible for its content. The data may have changed since that time. Click here to search real time questions/answers from Yahoo! Answers.